┌ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┬ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┐ 
│ │ Electricity 380 V ± 5% │ 50 Hz 
Phase + neutral │ │ │ 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
Fluid heating H2O │ │ │ 75 65  C 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
Water for humidifying Bar │ │ 3 │ 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
Water for cooling │ ____ │ │  C 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
Compressed air drying and │ │ │ Bar 3 
│ │ │ Waste 
└ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┘ 
1.3 weather conditions 

                         ┌ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┬ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┐ 
                         Temperature  C │ │ │% Relative Humidity 
                         Corresponding │ │ │ 
    ┌ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    Maximum values │ │ 32 │ 43 │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    Minimum values │ │ 5 │ 80 │ 
    └ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┘ 

1.4 CONDITIONS IN ROOM 

    ┌ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┬ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┬ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┐ 
    Temperature  C │ │ │ │% Relative Humidity 
    Room │ │ Inver. Max est │ │ 
    │ │ (1) │ (2) │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    WEAVING │ │ │ 70 │ 20 29.6 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    PREPARATION 20 29.6 │ │ │ 70 │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    │ │ ____ ____ ____ ____ │ │ 
    └ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┘ 

    (1) Tolerance ± 1  C 
Absolute value depends on the wet bulb outside, determined by adding 7.6  C per Buldo humid outside. 

(2) Tolerance ± 2.5% points 

The above mentioned values means measured at 1.5 meters above the floor and away from heat sources. 

2.0 INSTALLATION DATA 

2.1 ROOM 

                         ┌ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┬ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┬ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┐ 
                         Sala Sala │ │ │ │ Hall 
                         WEAVING PREPARATION │ │ │ ____ │ 
┌ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
Space m2 │ │ 1280 │ 595 │ ____ │ 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
Volume m3 │ 5120 │ 2380 │ │ ____ │ 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
Lighting Kw │ │ 20 │ 5 │ │ 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
Electrical consumption ____ │ │ │ 30 │ ____ │ 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
│ Coeff. use 95% │ 65 │ │ ____ │ 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
Power consumption 308 Kw │ │ │ 19.5 │ ____ │ 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
│ Air technological m3 / h │ │ ____ ____ ____ │ │ 
├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
│ Depression mm.ca │ │ │ │ 
    Users │ │ │ ____ ____ ____ │ │ 
    └ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┘ 
  

2.2 Installations CONDITIONING 

                             ┌ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┬ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┬ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┐ 
                             Sala Sala │ │ │ │ Hall 
                             WEAVING PREPARATION │ │ │ ____ │ 
    ┌ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    DUAL DUAL │ │ System │ │ ____ │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    │ Airflow m3 / h │ 90,000 │ 20,000 │ ____ │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    │ handling unit n  │ 3 │ 1 │ ____ │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    │ Type │ Unit AP 20 AP 30 │ │ ____ │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    │ recirculation environment  n / h │ 17.5 │ 8.5 │ ____ │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    │ Power Mech. Rated │ │ │ │ 
    │ dearomatized axis Kw / h │ 48 │ 13 │ ____ │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    Electric power │ │ │ │ │ 
    Kw │ 61.5 │ 17.5 │ │ ____ │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    Heating requirements │ │ │ │ │ 
    │ start Kcal / h │ 180,000 │ 100,000 │ ____ │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    │ Max water consumption m3 / h 0.96 │ 0:24 │ │ ____ │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    Requirements refrigerator │ │ │ │ │ 
    │ frig / h │ │ ____ ____ ____ │ │ 
    ├ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┤ 
    │ Water flow │ │ │ │ 
    │ to + /  C l / h │ │ ____ ____ ____ │ │ 
    └ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┴ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ┘ 

3.0 SUPPLY LIST 

3.1 WEAVING 

     conditioners mod n 3. DUAL AP 30 from 30,000 m3 / h, each consisting of: 
         N  1 Cassoncino discharge outdoor air and recirculated run with extruded aluminum honeycomb panels and galvanized sheet metal and plastic insulated with injected polyurethane rigid foam density 40 kg/m3 in thickness 20 mm. 
              On one side there will be a door handle inspection. 
         n 1  multiple shutter blades made of extruded aluminum bushings rotating on Teflon, with a galvanized steel frame to contain leverage and control for external profiles suitable tightness are present on the blades and chassis which is externally insulated with condensation functions. 
         N  1 servo pneumatic piston complete with plates, levismi and leading position. 
         N  1 centrifugal blower d.Ä. high-efficiency impeller galvanized steel blades aerodynamic profile, complete with light alloy crankcase, engine power, transmission of motion, vibration joints where necessary, with the following features: 
              Rated flow ........ 30.000 m3 / h 
              Installed power ..... 9.2 Kw 
         N  1 Cassoncino spraying water, model "AP", run in galvanized sheet steel with double inspection door handle, complete with: 
                ramp nozzle thick galvanized steel; 
                nozzles micronisers sunscreen and wear resistant alloy ferrule; 
                Profiles rolling of extruded PVC 
(Exclusive MARTEL Ltd.). 
  

         N  1 Group pressurized water, model "AP", consisting of: 
                water filter cartridge, with quick wash in counter; 
                5-piston pump, with motor and inverter control; 
                supply piping, type armored, complete with safety valve and pressure gauge. 

         N  1 line supersaturated air diffusion profile specific run in galvanized sheet steel, complete with shutter calibration tile drip less, support brackets, gaskets, clamps, bolts and galvanized support general accessories such as cables of galvanized steel, clamps, turnbuckles, Thimbles etc.. 
         N  1 outdoor air intake duct runs in "PIRAL, two sheets of aluminum sheet with interposed panel of polyurethane resin condensate, frames, counterframes PVC, gaskets and galvanized bolts and nuts. 
         n 1  Grid rain led to the above made of sheet steel galvanized profile. 

    n  3 groups recovered again, each consisting of: 
         N  1 Cassoncino shooting air run with extruded aluminum honeycomb panels and galvanized sheet metal and plastic insulated with injected polyurethane rigid foam density 40 kg/m3 in thickness 20 mm. 
              On one side there will be a door handle inspection. 
         N  1 Cassoncino removal / recirculation air run with extruded aluminum honeycomb panels and galvanized sheet metal and plastic insulated with injected polyurethane rigid foam density 40 kg/m3 in thickness 20 mm. 
              On one side there will be a door handle inspection. 
         n  2 multiple shutter blades made of extruded aluminum bushings rotating on Teflon, with the containment frame in galvanized steel and levers to control external tightness Suitable profiles are on the blades and chassis which is externally insulated with condensation functions. 
  

         n  2 servo pneumatic piston complete with plates, levismi and pilot positioner. 
         N  1 centrifugal blower d.Ä. high-efficiency impeller galvanized steel blades aerodynamic profile, complete with light alloy crankcase, engine power, transmission of motion, vibration joints where necessary, with the following features: 
              Scope ................ 28,000 m3 / h 
              Installed power ..... 9.2 Kw 
         N  1 eject air duct runs in "PIRAL", two sheets of aluminum sheet with interposed panel of polyurethane resin condensate, frames, counterframes PVC, gaskets and galvanized bolts. 
         n 1  Grid rain led to the above made of sheet steel galvanized profile. 

    n  3 groups of heating air, each consisting of: 
         n 1  exchange coil made with finned tubes belonging to collectors equipped with shell attacks containment flange. 
         n 1  pneumatic modulating valve to adjust the industrial thermal fluid. 

    n 3  recirculated air filters with a galvanized steel structure in nylon mesh filter media suitable for lint and grit. 

    N  1 Painting electronic tire, bi area for the control and command of equipment adjustment, with: 
         N  1 Painting containment equipment with protection 
   IP 55. 
N  1 Master power, complete with fuse protection. 
N  1 gearbox voltage stabilizer for power regulator. 
  

         N  1 multiadjustment configurable microprocessor modules and eight control, two analog outputs, six digital outputs. 
Prepared for connection to the display system using serial communication line 
Front-panel mounting, complete with digital display. 

   n  2 pressure gauge control pressure: 0 30 psi 
         Group 1 n  reducing air filtration. 
      n 4  PTC Temperature probes complete with polycarbonate enclosure protection IP 54 Range 0 to 50  C 
n  2 capacitive type humidity probe, complete with a polycarbonate enclosure IP 54 range 0 100% RH 
     Accessories for the implementation of the pneumatic circuit such as polyethylene pipes, fittings, clevises, bolts and fixing brackets. 

    N  1 Control panel for protection of electrical equipment suitable for installation inside the plant, consisting of: 
           hood fairing painted ns. color identification; 
           door with windows and dual-key system with dust seals; 
           hinged panel for protection and support with safety lock; 
  switch with lock; 
  telesalvamotori pole with coils; 
  LED indicators identifying and platelets; 
  valves and fuses for protection; 
  switches with two positions; 
           internal wiring, terminal blocks, mounting accessories and hardware changes. 

3.2 CHARGE AFONIZZAZIONE 

    n  6 Groups afonizzatori for the reduction of external noise, executed with phono-absorbent elements, resonators, rock wool, covered in aluminum. 

3.3 CHARGE DEVIATION air expelled 

    n 1  curve run in galvanized sheet steel, complete with internal anti-condensation insulation, frames, counterframes, gaskets and galvanized bolts. 
    n  9 trunks run in galvanized sheet steel, complete insulation internal condensation, frames, counterframes, gaskets and galvanized bolts. 

3.4 MICRO SECURITY CHARGE 

    n  12 Micro safety inspection on doors, to stop the installation. 
NB : The provision covers only the preparation and not the wiring that is at your expense as to exclusions attached. 

3.5 STEEL PIPE CHARGE 

     Number of distribution channels air in the room made of stainless steel flanges, complete with zinc, cadmium-plated bolts and gaskets as represented on ns. drawings. 

3.6 PREPARATION 

    n 1  conditioner mod. DUAL AP 20 from 20,000 m3 / h, consisting of: 
         N  1 Cassoncino discharge outdoor air and recirculated run with extruded aluminum honeycomb panels and galvanized sheet metal and plastic insulated with injected polyurethane rigid foam density 40 kg/m3 in thickness 20 mm. 
              On one side there will be a door handle inspection. 
         n 1  multiple shutter blades made of extruded aluminum bushings rotating on Teflon, with a galvanized steel frame to contain leverage and control for external profiles suitable tightness are present on the blades and chassis which is externally insulated with condensation functions. 
         N  1 servo pneumatic piston complete with plates, levismi and leading position. 
         N  1 centrifugal blower d.Ä. high-efficiency impeller galvanized steel blades aerodynamic profile, complete with light alloy crankcase, engine power, transmission of motion, vibration joints where necessary, with the following features: 
              Rated flow ........ 20.000 m3 / h 
              Installed power ..... 7.5 Kw 
         N  1 Cassoncino spraying water, model "AP", run in galvanized sheet steel with double inspection door handle, complete with: 
                ramp nozzle thick galvanized steel; 
                nozzles micronisers sunscreen and wear resistant alloy ferrule; 
                Profiles rolling of extruded PVC 
(Exclusive MARTEL Ltd.). 
         N  1 Group pressurized water, model "AP", consisting of: 
                water filter cartridge, with quick wash in counter; 
                5-piston pump, with motor and inverter control; 
                supply piping, type armored, complete with safety valve and pressure gauge. 
  

  
N  1 line supersaturated air diffusion profile specific run in galvanized sheet steel, complete with shutter calibration tile drip less, support brackets, gaskets, clamps, bolts and galvanized support general accessories such as cables of galvanized steel, clamps, turnbuckles, Thimbles etc.. 
         N  1 outdoor air intake duct runs in "PIRAL, two sheets of aluminum sheet with interposed panel of polyurethane resin condensate, frames, counterframes PVC, gaskets and galvanized bolts and nuts. 
         n 1  Grid rain led to the above made of sheet steel galvanized profile. 

    n  Group 1 regained strength, consisting of: 
         N  1 Cassoncino shooting air run with extruded aluminum honeycomb panels and galvanized sheet metal and plastic insulated with injected polyurethane rigid foam density 40 kg/m3 in thickness 20 mm. 
              On one side there will be a door handle inspection. 
         N  1 Cassoncino removal / recirculation air run with extruded aluminum honeycomb panels and galvanized sheet metal and plastic insulated with injected polyurethane rigid foam density 40 kg/m3 in thickness 20 mm. 
              On one side there will be a door handle inspection. 
         n  2 multiple shutter blades made of extruded aluminum bushings rotating on Teflon, with the containment frame in galvanized steel and levers to control external tightness Suitable profiles are on the blades and chassis which is externally insulated with condensation functions. 
         n  2 servo pneumatic piston complete with plates, levismi and pilot positioner. 
         N  1 centrifugal blower d.Ä. high-efficiency impeller galvanized steel blades aerodynamic profile, complete with light alloy crankcase, engine power, transmission of motion, vibration joints where necessary, with the following features: 
              Scope ................ 18.000 m3 / h 
              Installed power ..... 9.2 Kw 

  
N  1 eject air duct runs in "PIRAL", two sheets of aluminum sheet with interposed panel of polyurethane resin condensate, frames, counterframes PVC, gaskets and galvanized bolts. 
         n 1  Grid rain led to the above made of sheet steel galvanized profile. 

    N  1 Group Air Heating, consisting of: 
         n 1  exchange coil made with finned tubes belonging to collectors equipped with shell attacks containment flange. 
         n 1  pneumatic modulating valve to adjust the industrial thermal fluid. 

    N  1 recirculated air filter frame in galvanized steel and nylon mesh filter media suitable for lint and grit. 

    N  1 Painting electronic tire, bi area (for control of a zone texture), for the control and command of equipment adjustment, with: 
         N  1 Painting containment equipment with protection 
   IP 55. 
N  1 Master power, complete with fuse protection. 
N  1 gearbox voltage stabilizer for power regulator. 
         N  1 multiadjustment configurable microprocessor modules and eight control, two analog outputs, six digital outputs. 
Prepared for connection to the display system using serial communication line 
Front-panel mounting, complete with digital display. 
  

n 4  Transducers electropneumatic regulators for incremental digital input signal at three points out 3 15 psi 
   n 4  pressure gauge control pressure: 0 30 psi 

         Group 1 n  reducing air filtration. 
      n 4  PTC Temperature probes complete with polycarbonate enclosure protection IP 54 Range 0 to 50  C 
n  2 capacitive type humidity probe, complete with a polycarbonate enclosure IP 54 range 0 100% RH 
     Accessories for the implementation of the pneumatic circuit such as polyethylene pipes, fittings, clevises, bolts and fixing brackets. 

    N  1 Control panel for protection of electrical equipment suitable for installation inside the plant, consisting of: 
           hood fairing painted ns. color identification; 
           door with windows and dual-key system with dust seals; 
           hinged panel for protection and support with safety lock; 
  switch with lock; 
  telesalvamotori pole with coils; 
  LED indicators identifying and platelets; 
  valves and fuses for protection; 
  switches with two positions; 
           internal wiring, terminal blocks, mounting accessories and hardware changes. 

3.7 CHARGE EXTENSION duct 

         Set of pipes connected air conditioner pipe diffusion, performed in galvanized sheet steel, galvanized, complete with flanges, bolts cadmium and seals as represented on ns. drawings. 

3.8 MICRO SECURITY CHARGE 

    n 4  Micro safety inspection on ports for la'rresto installation. 
NB : The provision covers only the preparation and not the wiring that is at your expense as to exclusions attached. 

3.9 STEEL PIPE CHARGE 

     Number of distribution channels air in the room made of stainless steel flanges, complete with zinc, cadmium-plated bolts and gaskets as represented on ns. drawings.